Signify Classified - Internal#
Hue Engine 9290024695
Specification item
Description
Logistical data
12NC
Minimum Order Quantity
Electrical input data
Vcc voltage
Current (normal)
Electrical output data
Average power consumption
Standby power
Wiring & Connections
Ground
ADC2, e.g. for voltage sensing General purpose in/out 2
ADC1, e.g. for current sensing
to be used as ADC (e.g. NTC read-out), I2C, SPI or PWM
to be used as ADC, I2C, SPI or PWM PWM_CHN1
General purpose in/out 1: E.g. for button control
General purpose in/out 2: E.g. for button controlPWM_CHN3
i.e. for current source
PWM output
PWM output
PWM output
PWM output
PWM output
Ground
3V power in
Used for SW programming, UART bus communication
Used for SW programming, UART bus communication
Used for SW debugging
Used for SW debugging
Used for SW debugging
Features & Functions
Hue White Color Ambience
Hue White Ambiance
Hue White
Dimming
Device diversity
Automatic color consistency
OTA upgrade
Wireless specifications
Wireless RF mode frequency band
Wireless communications protocol
Operating channel
Range
Frequency tolerances (Typical)
Output power (Typical)
EVM (Typical)
Receiver Sensitivity (Typical)
TRP
LED board requirements
Hue White Color Ambience
Value
Unit
Condition
Hue Engine is second generation of a general purpose Zigbee& BLE
certified building block for Hue connected lighting applications
e.g. Hue White, Hue White Ambiance and Hue White and Color
ambiance for lamps and luminaires.
Ripple<50 mV
I/O definition
PCE
Volt
mA
Watt
GND
ADC2
ADC1
Mixed_out_1
Mixed_out_2
GPIO1
GPIO2
Enable
PWM_CH0
PWM_CH1
PWM_CH2
PWM_CH3
PWM_CH4
GND
VDD
TXD
RXD
Nreset
SWCLK
SWDIO
929002469501
500
3.0~3.6
18
60mW
<100mW
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
yes
yes
yes
yes
yes
yes
yes
2400–2483.5 MHz
IEEE 802.15.4
Bluetooth LE
Zigbee 11 – 26
Bluetooth 0-39
12
+/-40
9
18
-102
6
MHz
ZigBee protocol
Bluetooth LE protocol
channels
meter
ppm
dBM
%rms
dBM
dBM
Unified Gamut
Tunable white CCT range: 2000-6500K
Over the air upgradable when connected to the Hue Bridge
by late state configuration
indoor
Continuous single tone
Measured at antenna feedpoint
conducted sensitivity
when mounted on a motherboard of 30x40mm (i.e. Hue Connect)
covered by L1.5 specifications
Signify Classified - Internal#
Hue White
Insulations
Dimensions & Weight
Length
Width
Height
Fixing hole diameter
Fixing hole distance
Weight
Operational temperatures and humidity
Ambient temperature
Tcase-max
Maximum housing temperature
Relative humidity
Enviroment
Storage temperature and humidity
Ambient temperature
Relative humidity
Lifetime
lifetime
Surge capability
ESD rating
Certificates and standards
Approval marks
Compliances and approvals
Hue White Ambiance
Tunable white CCT range: 2000-6500K
2700K / 3000K / 4000K
covered by L1.5 specifications
covered by L1.5 specifications
covered by L1.5 specifications
±10% tolerance
±10% tolerance
±10% tolerance
Non-condensing
For 6 months
Non-condensing
Contact
Air
Measured temperature at Tc-point is Tcase- max.
Maximum failures = 10%
-20 - 75°C
to be measured on Hue Engine shield
23.5
18
3.5
NA
NA
Damp
+/-2
+/-4
mm
mm
mm
mm
mm
gram
Celcius
Celcius
hours
KV
KV
CE, FCC, RED, ROHS & REACH, Zigbee, BLE
Signify Classified - Internal#
FCC
FCC Labelling Requirements
When integrating HUE Engine into a product it must be ensured that the FCC labelling
requirements are met. This includes a clearly visible label on the outside of the finished
product specifying the FCC identifier (FCC ID: 2AGBW9290024695X). This exterior label can
use wording such as “Contains Transmitter Module FCC ID: 2AGBW9290024695X” although any
similar wording that expresses the same meaning may be used.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
The advance interface module complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
The module and associated antenna must be installed to provide a separation distance of at
least 20cm from all persons and must not transmit simultaneously with any other antenna or
transmitter. and it needed for the host product manufacturer to provide to end users in
their end-product manuals. If RF exposure statements and use conditions are not provided,
then the host product manufacturer is required to take responsibility of the module through
a change in FCC ID (new application).
FCC Approvals
FCC statement:
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
FCC notice:
This device is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules)
listed on the grant, and that the host product manufacturer is responsible for compliance to
any other FCC rules that apply to the host not covered by the modular transmitter grant of
certification and the final host product still requires Part 15 Subpart B compliance testing
with the modular.
This device has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This device
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the device and receiver
Connect the device into an outlet on a circuit different from that to which
the receiver is connected
Consult the dealer or an experienced radio/television technician for help .
Please take attention that changes or modification not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Signify Classified - Internal#
IC
IC (ISED Canada) Approvals
This device complies with ISED Canadalicense-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired
operation of the device.
Under ISED Canadaregulations, this radio transmitter may only operate using an antenna of a
type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
permitted for successful communication
This module complies with ISED CanadaRF radiation exposure limits set forth for general
population. To maintain compliance, this module must not be co-located or operating in
conjunction with any other antenna or transmitter. The module and associated antenna must be
installed to provide a separation distance of at least 20 cm from all persons and must not
transmit simultaneously with any other antenna or transmitter.
Immediately following the above notice, the manufacturer shall provide a list of all
antenna types approved for use with the transmitter, indicating the maximum permissible
antenna gain (in dBi) and required impedance for each.
Class B Notice for Canada This Class B digital apparatus complies with Canadian ICES-003.
The labelling requirements for ISED Canadaare similar to those of the FCC. Again a clearly
visibly label must be placed on the outside of the finished product stating something like
“Contains Transmitter Module, IC: 20812-24695X”, although any similar wording that
expresses the same meaning may be used.
Le présent appareil est conforme aux CNR d’lndustrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) I’
appareil ne doit pas produire de brouillage, et (2)I’utilisateur de I’appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
En vertu de la réglementation d’Industrie Canada, cet émetteur radio risquera uniquement à
l’aide d’une antenne de type et de gain maximum (ou moins) pour l’émetteur a approuvé par
Industrie Canada. Pour réduire les interférences radio potentielles à d’autres
utilisateurs, le type d’antenne et son gain doivent être choisies que la puissance isotrope
rayonnée équivalente (p.i.r.e.) n’est pas plus que celle autorisée pour une communication r
éussie
Cet émetteur ne doit pas tre Co-placé ou ne fonctionnant en même temps qu'aucune autre
antenne ou émetteur. Cet équipement devrait être installé et actionné avec une distance
minimum de 20 centimètres entre le radiateur et votre corps.
Ce module est conforme à la FCC et Industrie Canada RF limites d’exposition aux
rayonnements définies pour l’ensemble de la population. Pour maintenir la conformité, ce
module ne doit pas être co-implanté ou fonctionner en conjonction avec toute autre antenne
ou émetteur
À la suite de l’avis ci-dessus, le fabricant doit fournir une liste de tous les
types d’antenne approuvés pour une utilisation avec l’émetteur, indiquant au maximum
gain d’antenne (en dBi) et impédance requise pour chacun.
Signify Classified - Internal#
CE
Les exigences d’étiquetage pour Industrie Canada sont semblables à celles de la FCC. Encore
une fois un clairement visiblement étiquette doit être placée à l’extérieur du produit fini
indiquant quelque chose comme "Module émetteur de Contains, IC ID: 20812-24695X", bien que
tout même libellé qui exprime que le même sens peuvent être utilisé.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada
European Certification (ETSI)
The module have been certified to the following standards:
• Radio: EN 300 328
• EMC: EN 301 489-1, EN 301 489-17
• EMF: EN 62479
• Safety: EN 61347-1, EN 61347-2-11
If the module is incorporated into an OEM product, the OEM product manufacturer must ensure
compliance of the final product to the European Harmonized EMC, and low voltage/safety
standards