DVD-ROM DRIVE SD-816 User's Guide FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaran-
tee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Re-orient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. http://www.samsung-ODD.com www.samsungelectronics.com BG68-00613A Rev.00 Safety Precautions Your DVD-ROM Drive Upgrading the Firmware Flash Memory Connecting the Cables The following diagrams illustrate the precautions to be taken when using your DVD-ROM drive. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment You must not use the drive in any manner other than that specified in this guide. CAUTION Do not attempt to repair the DVD-ROM drive yourself. Contact your dealer or local SAMSUNG representative for all repairs. If you make any adjustments or perform any operations other than those specified in this guide, you run the risk of exposure to hazardous radiation. Avoid exposing your eyes or skin to direct or scattered radiation. WARRANTY Please refer to the Samsung limited warranty statements. Precautions 1. To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. 2. Always check each disc for cracks before using it. If there are cracks on the surfaces, especially around the border of the cen-
ter hole, we recommend that you make a copy of the disc immediately and then stop using it. If you continue using the disc, it will probably develop more cracks and eventually cause irreparable damage. 3. Do not use poor quality discs:
G From unknown sources G Without any copyright G Scratched or damaged in any way 1 1 2 3 4 5 6 1. Connector for stereo headphones with a 3.6 mm stereo mini-jack 2. Headphone volume control 3. Disc compartment (the compartment opens and closes automatically when you press the Eject button) 4. Emergency eject hole (if the compartment does not open when you press the Eject button, power off the computer, insert a pin or unfolded paper clip in the hole and push firmly) 5. Indicator light (when it is green, a disc is being read) 6. Eject button The product firmware can be upgraded by downloading the updated file from the following Web site:
http://www.samsung-ODD.com www.samsungelectronics.com System Requirements Before you install the DVD-ROM drive, we strongly recommend that you check that your setup meets the system requirements listed below. Item Computer Disk space Windows version Description Intel Pentium III (or higher), 350MHz or higher, 128 MB of RAM (or higher) with an IDE interface 100 MB minimum Windows 95 OSR2 / 98 / 2000 / ME / XP /
Windows NT 4.0 (or higher)
* This product has been set at the UDMA mode. It may cause trouble due to the compatibility of a specific board or system. In this case, download the latest version of Firmware which supports the DMA Mode. Using the DMA mode may slightly decrease the efficiency of DVD-ROM. Installing the DVD-ROM Drive 1. Power cable 2. Master/slave select terminal 3. IDE cable 4. Audio cable 1 Connecting the power cable The 4-pin power cable from the internal power unit of your computer must be connected to the power terminal on the rear of the DVD-ROM drive. 2 Installing a jumper on the master/slave select terminal Install the jumper in the correct position on the terminal:
MA to use the device in the master mode SL to use the device in the slave mode CS to control the device via a CSEL host interface signal See Step 3 for further details. 3 Connecting the IDE cable Two configurations are possible. To install your DVD-ROM drive in the PC, proceed as follows. G The DVD-ROM drive is the only IDE device in addition to the hard disk. 1 5 1. Two-pin digital audio output terminal for use with a sound or 2 3 4 MPEG card supporting digital audio features 2. Four-pin sound output terminal for use with a sound card (refer to the sound card documentation for further details) 3. Master/slave select terminal 4. 40-pin host IDE interface connector 5. 4-pin power terminal 2 1 Make sure that the PC is powered off and disconnected from any power source. 2 If necessary, attach a horizontal bracket to both sides of the drive. G Use of the brackets depends on your computer model; you can purchase these accessories separately from your computer dealer. 3 Remove the cover from a free expansion slot and install the DVD-ROM drive, as shown in the illustration. G If you have no free expansion slot, install the drive in place of the diskette drive. Install the jumper in the SL position (Slave). Connect the 40-pin flat IDE cable from the IDE port on the mother board, first to the DVD-ROM drive and then to the hard disk. IDE port Mother board DVD-ROM Hard disk
(SL)
(MA) G You already have an additional IDE device installed in your computer. Second IDE cable First IDE cable Mother board DVD-ROM CD-ROM
(MA)
(SL) Hard disk
(SL) Hard disk
(MA) Install the jumper in the MA position (Master). Connect the 40-pin flat IDE cable from a second IDE port on the mother board directly to the DVD-ROM drive or first to another additional IDE drive and then to the DVD-ROM drive. DVD-ROM drive 3 4 Connecting the audio cable from a sound card Connect the 4-pin audio cable between the sound output terminal on the DVD-ROM drive and the audio input terminal on the sound card. 4 Setting Up the Device Driver Installing the Device Driver Using the DVD-ROM Drive Solving Technical Problems Technical Specifications N Automatic Setup 1 Insert the setup diskette in the diskette drive and change the directory to A:, where A: is the diskette drive. To do so, type A: after the C:\ prompt and press [Enter]. 2 Type CDSETUP and press [Enter]. 3 Reboot the computer. N Manual Setup 1 Make the C:\SAMSUNG directory. 2 Copy the files from the diskette to the C:\SAMSUNG directory. To do so, type COPY A:*.* C:\SAMSUNG after the C:\ prompt and press
[Enter]. 3 Edit the CONFIG.SYS file. Add the DEVICE=C:\SAMSUNG\SSCDROM.SYS \D:SSCD000 /V entry. LAST DRIVE = Z
DEVICE = C :\SAMSUNG\SSCDROM.SYS /D : SSCD000 /V 4 Edit the AUTOEXEC.BAT file. Add the C:\SAMSUNG\MSCDEX /D:SSCD000 entry.
C :\SAMSUNG\MSCDEX /D:SSCD000 5 Reboot the computer. No additional device driver is needed for Windows 95/98/2000/ME/XP/NT, as the default Windows device driver is used. You can check that the DVD-ROM drive has been correctly detected by Windows. To do so, proceed as follows. 1 Double-click on the My Computer icon on your desktop. 2 Double-click on the Control Panel folder. 3 Double-click on the System icon. 4 Click on the Device Manager tab. 5 Expand the CD-ROM branch. The SAMSUNG DVD-ROM SD - *** device name is displayed. The SAMSUNG device driver enables discs in the DVD-ROM drive to be read but not recorded in an MS-DOS environment; the driver is located in the D driver folder on the CD record utility disc. DVD Region Protection Coding (RPC):
The RPC feature is supported on DVD players and is used with DVD-video discs (such as movies). Currently, the motion picture industry has divided the world into different regions or zones that correspond to the regional markets into which the motion picture industry releases movies. Simply put, RPC codes are placed on movies marketed throughout the world, based on the region of the world in which they are being sold. These RPC codes help control and pre-
vent pirating of new movies into other motion picture regions prior to their true release dates within those markets. The SD-816 DVD-ROM drive supports RPC phase II. In the RPC-2 mode, the local code can be changed by users. RPC-2 is selected by default for the SD-816 DVD-ROM drive. You can change the region code up to five times via an MPEG application. Please contact your dealer or local SAMSUNG representative if you wish to change the local code more than five times. To play audio or video CDs in your DVD-ROM drive, proceed as follows. 1 Push the power button and boot the computer. 2 After booting the computer, open the disc compartment by pressing the Eject button. 3 Insert the disc (CD/DVD) with the label on the disc facing upwards and close the disc compartment by pressing the Eject button. The indicator light comes on. 4 Play the disc (CD/DVD). Playing Audio CDs Run the CD player supplied with Windows or your sound card. You can listen to the CD by connecting headphones to the appropriate connector. If you have installed the appropriate player, such as Microsoft Windows Media Player, you can adjust the volume using the headphone volume control on the drive front panel. Playing Video CDs Set up and run the SOFT MPEG program. Storing and Cleaning Your Discs To ensure a long service life for your discs and drive, follow the precautions below when storing and cleaning your discs. 1 Do not place a disc in direct sunlight. 2 Store a disc vertically in a well-ventilated and stable location. 3 Do not write or attach a label on a disc. 4 Do not drop a disc or place heavy objects on it. 5 Do not touch the surface of a disc; hold it by the edges. 6 To clean a disc, polish lightly from the inside of the disc to the outside with a soft cotton cloth. 7 Do not leave the disc compartment open when you are not using it. Problem The DVD-ROM drive is not detected by the computer. After installing the DVD-ROM drive, the PC gets slower. The DVD-ROM drive is not recognized by MS-DOS. The DVD-ROM drive is not detected by Windows. No sound is heard from an audio CD. A CD is not read or is read too slowly. The disc compartment will not open. Meaning / Solution N Check that the power, audio and IDE cables are correct-
ly connected to the computer. N Change the IDE cable and reconnect it to the computer. Preferably, connect a second IDE cable to the DVD-ROM drive in master mode; see page 7 for further details. N Check the position of the jumper in the master/slave select terminal. N Reinstall the device driver or update it with the latest version by downloading it from the Samsung Web site.
- www.samsung-ODD.com
- www.samsungelectronics.com N This case may occur when there is a Windows instal-
lation problem; reinstall Windows. N Check whether the audio cable is correctly connected to the sound output terminal on the DVD-ROM drive and the sound card CD-IN terminal. N Check that the sound card is operational. N Adjust the volume control. N Install the latest version of the device driver. N Check whether the CD is of good quality and clean it, if necessary. N Check that the power cable is correctly connected. N Power off and disconnect the PC. Insert a pin or unfolded paper clip in the emergency hole and push firmly until the disc compartment opens. When the MPEG software plays a Video CD, the pictures are not regu-
lar and the running speed is too slow. N Adjust the size of the replay screen. N After checking the display resolution, adjust it, if necessary. The Disc is not in message is displayed even though a disc has been inserted. The DVD-ROM drive is not detected after it is connected to a sound card. N The computer may not recognize the disc if you start playback too quickly after inserting the disc. Open and close the disc compartment and try again. N Clean the disc and try again. N The interface mode of the sound card is AT-BUS. You must therefore connect the DVD-ROM drive to the IDE port on the PC mother board, rather than to the sound card, or install an IDE-compatible sound card. SAMSUNG continually strives to improve its products. Both the design specifications and these user instructions are thus subject to change without notice. ITEM SD - 816 DVD CD DISC Disc types supported Disc diameter DVD-ROM, DVD-VIDEO, DVD-R, DVD-RW, DVD-RAM, CD-DA(Audio), CD-ROM, CD-ROM XA, CD-Plus, CD-Extra, Photo-CD(Single,Multi-session), Video CD ready, Enhanced CD, CD-I/FMV, CD-R, CD-TEXT, CD-RW 120mm or 80mm DRIVE PERFORMANCE Data transfer rate Access time(1/3Typical) Data buffer capacity Laser Slide mechanism Spindle motor Loading mechanism ERROR RATE FRONT PANEL REAR PANEL OPERATING ENVIRONMENT GENERAL Eject button Indicator(LED) Headphone output Volume control Required power Interface connector Audio output Jumper block Operation Storage Dimensions Net weight RELIABILITY MTBF Max. 21,600KB/sec (16X) / Max. 7,200KB/sec (48X) Sustained :
PIO Mode 4 : 16.6MB/sec Multiword DMA mode 2 : 16.6MB/sec UDMA mode 2 : 33MB/sec 95ms(Typical) 100ms(Typical) 512KB Semiconductor Laser Stepping motor Brushless motor Tray. DC motor(Soft Eject). Horizontal/Vertical 10-15 / MODE1:10-12, MODE2:10-9 Auto eject or Auto inject BUSY Stereo mini-jack(3.6mm) 0.60V20%(rms) 33 Wheel knob
+5VDC : 2.0A, +12VDC : 1.0A ATAPI Line out 0.70V 20%(rms) : 47K Device configuration jumper Temperature : 5 ~ 45C, Humidity : 10 ~ 80%
Temperature : -25 ~ 60C, Humidity : 10 ~ 90%
148.2(W) x 42(H) x 184(D)mm 740g 125,000 POH(Duty 20%)
* In case of the PC without UDMA, it may have a different DVD data transmission rate. 5 6 7 8 9 DVD-ROM LAUFWERK SD-816 Bedienungsanleitung Einbauen des DVD-ROM Laufwerks Bauen Sie das DVD-ROM Laufwerk in horizontaler Lage in den Computer ein. Achten Sie dabei darauf, da sich die Taste Open/Close auf der rechten Seite befindet. Zum Einbauen des Laufwerks ist folgendermaen vorzugehen:
1 Den Computer ausschalten. Nicht vergessen, die Einstellung des Konfigurations-Jumpers auf der Rckseite des DVD-ROM Laufwerks zu berprfen. 2 Die Abdeckung vom PC (Zentraleinheit des Computers) abnehmen. 3 Die Blende fr die 5,25-Zoll-Einheit, in der das DVD-ROM Laufwerk installiert werden soll, entfernen. 4 Das IDE Schnittstellenkabel und die Stromversorgungskabel im Computer an das DVD-ROM Laufwerk anschlieen. Die Steckverbinder sind so beschaffen, da sie nur in einer Stellung passen. ben Sie keine Kraft aus, wenn sie nicht zu passen scheinen. 5 Das DVD-ROM Laufwerk in die Einheit einbauen und mit den Befestigungsschrauben (empfohlen werden Standardschrauben M3x6x4) befestigen. N Je nach PC-Modell mssen eventuell Fhrungsschienen an dem Laufwerk angebracht werden, damit das Laufwerk gut fixiert wird. N Wenn Schrauben verwendet werden, die lnger sind als die empfohlene Standardgre, kann das Laufwerk beschdigt werden. 6 Die Abdeckung wieder am PC anbringen. Sicherheitshinweise Vorderseite des DVD-ROM-Laufwerks Rckseite des DVD-ROM-Laufwerks System-Anforderungen Die folgenden Abbildungen veranschaulichen die Vorsichtsmanahmen, die bei der Benutzung des DVD-ROM-Laufwerks getroffen werden msen. Bei Aenderungen oder Modifikationen,die der Anwender ohne Bestaetigung vorgenommen hat, verliert der Anwender das Recht den Produkt zu benutzen. Das Laufwerk darf auf keine andere Weise benutzt werden als in diesem Handbuch beschrieben. ACHTUNG Versuchen Sie nicht, das DVD-ROM-Laufwerk selbst zu reparieren. Wenden Sie sich bei allen eventuellen Reparaturen an Ihren Hndler oder Ihre SAMSUNG-Vertretung vor Ort. Wasser und Feuchtigkeit vom Gert fernhalten, da sonst Gefahr durch elektrische Schlge besteht bzw. Gerteschden auftreten knnen. GARANTIE Garantie-Reparaturen mssen von Samsung-Fachhndlern oder Samsung-Vertragswerksttten ausgefhrt werden. Vorsichtsmanahme 1. Vor dem Gebrauch von Discs sollte man diese auf Sprnge kontrolieren. Fall ein Sprung vorhanden ist (besonders am Rande des Zentralloches), empfehlen wir dringend, eine Kopie der CD zu erstellen. Bei weiterem Benutzen der CD, knnen zustzliche Sprnge auftreten, die die CD zerstren und dadurch auch das Laufwerk. 2. Bei Benutzung von Discs achten Sie bitte auf gute Quallitt. Es finden sich immer wieder Produkte, die illegal hergestellt werden, verkratzt oder beschdigt sind.
* Beim Starten (SPIN-UP) und beim Anhalten(STOP) entsteht ein Reibungsgerusch. Dieses ist kein fehlerhaftes Gerusch sondern auf das ABS(Auto Balance Systeme) zurckzufhren. 1 2 3 4 5 6 1 2 3 4 5 1 Kopfhreranschlu An diese Buchse knnen Sie einen Stereo-Kopfhrer mit 3,6 mm-Klinkenstecker anschlieen. 2 Lautstrkeregler Mit diesem Regler wird die Lautstrke des Kopfhrers eingestellt. Der Kopfhrer-Anschlu und die Lautstrke-Einstelltasten sind nur funktionsfhig, wenn die erforderlichen Software-Utilities installiert wurden. Sie knnen zum Beispiel den Microsoft WINDOWS Media Player benutzen. 3 Discschublade Die Discschublade ffnet und schliet sich automatisch, wenn die Taste Open/Close gedrckt wird. 4 Notffnung Wenn sich die Schublade nach dem Drcken der Taste Open/Close nicht ffnet, stecken Sie einen kleinen Metallstiff (z.B. von einer aufgebogenen Broklammer) in dieses Loch, um die Schublade zu ffnen. 5 LED Sie leuchtet, wenn auf einer DVD/CD Disc ein Zugriff erfolgt. 6 Open/Close-Taste Drcken Sie diese Taste whrend der CD-ROM-Wiedergabe, um die CD zu stoppen. Bei gestoppter bzw. nicht eingelegter CD drcken Sie diese Taste, um die CD-ROM-
Schublade zu ffnen bzw. zu schlieen. 1 Digitaler Audioanschlu ber diesen Anschlu knnen Sie eine Karte die einen digitalen Ausgang besitzt an das Laufwerk anschlieen (z.B. manche Sound- oder MPEC-Karten). 2 Audio-Ausgangsanschlu ber diesen 4poligen Steckverbinder kann das Laufwerk mit einer Sound-Karte verbunden werden. Diese Funktion wird in der vorliegenden Anleitung nicht ausfhrlich beschrieben. Sehen Sie in der Dokumentation fr das Audio-Zubehr nach. 3 Jumper fr Gerte-Konfiguration Normalerweise sieht die vorgegebene Konfiguration wie folgt aus:
C S S L M A berprfen Sie, da die vorliegende Einstellung der abgebildeten Einstellung entspricht. Wenn dies nicht der Fall ist, einfach den Jumper entfernen und in die richtige Stellung bringen. 4 Host IDE-Schnittstellen- Anschlu Schlieen Sie das 40polige Flachbandkabel von der IDE-Schnittstelle an diesen Eingangs-/Ausgangs-Schnittstellen-Anschlu an. 5 Stromversorgungsanschlu Der Stromversorgungsanschlu ist ein vieradriger Stecker. Bevor Sie das DVD-ROM Laufwerk einbauen, sollten Sie sich unbedingt vergewissern, da Ihr Computer die nachstehenden System-Anforderungen erfllt. Betrifft... Art des Computers Beschreibung Intel Pentium III, 350MHz(oder mehr), RAM 128MB(oder mehr) mit einer IDE Schnittstelle
(oder ein 100% IBM-kompatibler Computer) Freier Speicherplatz auf Festplatte mindestens 100 MB Windows-Version ab 95 OSR2 / 98 / 2000 / ME / XP / NT 4.0
* Dieses Produkt ist auf dem UDMA-Modus eingestellt. Diese Einstellung kann aber im Zusammenhang mit der Kompatibilitt auf einer bestimmten Platte oder einem System Probleme verursachen. Im solchen Fall laden Sie bitte die Firmware Flash Memory herunter, die den DMA-Modus unterstzt. Bei Gebrauch des DMA-Modus kann die Kapazitt des DVD-Treibers leicht zurckgehen. N Regionale Codierung (RPC: Region Protection Code) Regionschutzcode (RPC) von DVD Discs: Diese Besonderheit wird vom DVD Abspielgerten untersttzt und wird fr die DVD Video Discs (z.B. Filme) bentigt. Die weltweite Filmindustrie hat die Welt in verschiedenen Regionen aufgeteilt. Diese Regionen oder Zonen beziehen sich auf die regionalen Filmmrkte in die Filme verkauft werden sollen. Durch einsetzen eines RPC Codes auf der CD kann diese nur in den freigegebenen Regionen, mit Abspielgerte dieses Codes, abgespielt werden. Der RPC Code soll vor Piraterie von neuen Filmen vorbeugen. Das DVD Laufwerk SD-816 untersttzt RPC der Phase II. RPC 2 lt die nderungen des Regionalcodes durch den Benutzer zu. Das DVD SD-816 Laufwerk hat RPC 2 als Standard. Der Regionalcode wird in der MPEG Software eingestellt und kann bis zu fnft mal von Benutzer verndert werden. 1 2 3 4 Anweisung fr den Gebrauch/Lagerung und Pflege von CDs Dies ist eine Anmerkung zur Vermeidung von Schden an Ihren CDs. Bitte beachten Sie die folgenden Hinweise. 1 Gebrauchsanweisung 1 2 Nach dem hochfahren des PCs, drcken Sie Starten des Computers. dieTaste zum ffnen/Schlieen der Disc-Schublade. 3 Nach dem Einschieben der Disc(CD/DVD) drcken Sie die Taste zum ffnen/Schlieen.
* damit die Disc-Schublade sich schliet. 4 Die Disc wird abgespielt. Spielen die Audio CDs
* Starten Sie das CD-Wiedergabeprogramm, das mit der Soundkarte geliefert wurde. Oder starten Sie das CD-Wiedergabeprogramm von WINDOWS.
* Durch Einstecken des Kopfhrers in den Kopfhreranschlu knnen Sie Musik hren. 2 Spielen die Video CDs
* Stellen Sie ein und fhren Sie das SOFT MPEG Programm aus. Discaufbewahrung 1 Nicht unter direkten Sonnenstrahleneinflu 2 Auf einen temperierten und ebenen Platz 3 Kein Kratzer, keine Aufkleber...usw. auf 4 Die Disc nicht zu stark pressen oder fallen aufbewahren. der Disc legen. lassen. 3 Discpflegemethode 1 Die Discoberflche nicht berhren sondern nur am Discrand anfassen. 2 Mit einem weichen Tuch die Disc von innen nach auen zum Rande leicht abwischen. Bei Berhrung der Discoberflche oder bei Flecken- oder Staubbedeckung der Disc kann eine Funktionsstrung auftauchen. Installieren der Treibersoftware Fr WINDOWS 95/98/ME/2000/XP/NT wird kein zustzlicher Gertetreiber bentigt. Es wird der im WINDOWS mitgelieferte Gertetreiber genutzt. N Automatische Installation 1 2 3 Die 3,5" SETUP Diskette ins FDD einfhren und dann auf das A: Laufwerk wechseln. G Das 3,5" FDD wird als A: Laufwerk betrachtet.
[C:\ A:] eingeben und EINGABE Taste drcken. Wenn im Display [A:\] erscheint, [CDSETUP] eingeben und die EINGABE Taste drcken. Die Treiber werden automatisch geladen. Nach der Installation den Computer neu starten. N Manuelles Installieren 1 2 3 4 5 Einen neuen Ordner anlegen [C:\SAMSUNG].
[SSCDROM.SYS] in diesen Ordner kopieren. G [C:\ COPY A:*.* C:\SAMSUNG] eingeben und dann EINGABE Taste drcken.
[CONFIG.SYS] Datei bearbeiten. G DEVICE=C:\SAMSUNG\SSCDROM.SYS /D:SSCD000 /V eingeben. LAST DRIVE = Z
DEVICE = C :\SAMSUNG\SSCDROM.SYS /D : SSCD000 /V
[AUTOEXEC.BAT] Datei bearbeiten. G C:\SAMSUNG\MSCDEX /D:SSCD000 eingeben.
C :\SAMSUNG\MSCDEX /D:SSCD000
Neustarten des Computer. Falls Probleme auftreten Beim Starten (SPIN-UP) und beim Anhalten(STOP) entsteht ein Reibungsgerusch Dieses ist kein fehlerhaftes Gerusch sondern auf das ABS(Auto Balance Systeme) zurckzufhren. Problem Das DVD-ROM Laufwerk wird nicht erkannt. Nach dem Einbau des DVD-ROM Laufwerkes verlangsamt sich die Geschwindigkeit des PCs. Das DVD-ROM Laufwerk wird unter DOS nicht erkannt. Das DVD-ROM Laufwerk wird unter WINDOWS nicht erkannt. Kein Klang aus der Audio CD Die CD wird nicht erkannt und die Geschwindigkeit verlangsamt sich. Der CD Schublade ffnet sich nicht. Beim Benutzen von S/W MPEC treten stndige Unterbrechungen der Video CD Wiedergabe auf, und die Geschwindigkeit verlangsamt sich. Anzeige " keine CD vorhanden"
trotz eingelegter Disc. Ursache/Abhilfe N berprfen der Strom-, Audio- und IDE Kabel. N Auswechseln des IDE Kabels ( Mglichst am anderen IDE Port verbinden ). N berprfen der Master/Slave Einstellung N Den DOS-Treiber wieder neu installieren oder eine neue Version des Treibers von der Samsung Homepage herunter laden und installieren.
- www.samsung-ODD.com
- www.samsungelectronics.com N Dieses kann auftreten bei einer fehlerhaften WINDOWS Installation. Dann sollte WINDOWS neu installiert werden. N berprfen des Audiokabels, ob es richtig mit dem DVD-ROM Laufwerk (Audioausgang) und der Soundkarte (CD IN ) angeschlossen ist. N berprfen der Funktionalitt der Soundkarte N Lautstrke verndern durch den Soundregler. N Installieren der neuesten Version des Treibers
( z.B. aus dem Internet ). N berprfen der CD. Gegebenenfalls reinigen. N berprfen der Strom zufuhr, ob das Stromkabel, richtig angeschlossen ist. N Einen kleinen Stift (z.B. Broklammer) in die Notffnung stecken und stark drcken. Die Schublade ffnet sich. N Verkleinern der Wiedergabebildflche auf dem Bildschirm. N berprfen der Auflsungsstufe des Bildschirms. Gegebenenfalls die Auflsungsstufe in der Systemsteuerung von WINDOW verndern. N Wenn die Starttaste zu schnell gedrckt wird, kann der Computer die Disc nicht erkennen. In diesem Fall ffnen und schlieen der Schublade und erneut versuchen. N Reinigen der CD und erneut versuchen. Technische Daten SAMSUNG ist dauernd bestrebt, ihre Erzeugnisse zu verbessern. Dadurch ndern sich Design und Bedienungsanweisungen jederzeit ohne vorherige Ankndigung. Betrifft... SD-816 DVD CD CD - Typen CD - Durchmesser DVD-ROM, DVD-VIDEO, DVD-R, DVD-RW, DVD-RAM, CD-DA(Audio), CD-ROM, CD-ROM XA, CD-Plus, CD-Extra, Photo-CD(Single,Multi-session), Video CD ready, Enhanced CD, CD-I/FMV, CD-R, CD-TEXT, CD-RW 80mm oder 120mm CD LEISTUNGS-
DATEN Datenbertragungs-
rate Zugriffszeit(1/3 Typisch) Datenpufferkapazitt Laser Bewegungsmechanismus Spindelmotor Lademechanismus FEHLERRATE BEDIENFELD VORDERSEITE RCKSEITE Open/Close-Taste LED-Anzeige Kopfhrer-AnschluB Lautstrkeregler Leistungsaufnahme Schnittstellen-Anschlu Audio-Ansgang Jumper-Block UMGEBUNGS-
BEDINGUNGEN ALLGEMEINES Gertebetrieb Lagerung Abmessungen Nettogewichtt ZUVERLSSIGKEIT MTBF Dauerleistung :
Max. 21,600KB/sec (16X) / Max. 7,200KB/sec (48X) PIO Mode 4 : 16.6MB/sec. Multiword DMA mode 2 : 16.6MB/sec UDMA mode 2 : 33MB/sec 95ms(Typisch) 100ms(Typisch) 512KB Halbleiter Laser Getriebemotor Stromrichter motor Disc-Schublade. Horizontal/Stehend 10-15 / Modus1:10-12, Modus2:10-9 Automatischer Einzug/Auswurf leuchtet bei Betrieb Stereoklinkenstecker(3.6mm) 0.60V20%(vrms)33 Rndelrad
+5V Gleichspannung, 2.0A, +12V Gleichspannung,1.0A ATAPI Line out 0.70V 20%(vrms) : 47K Jumper fr Gerte-Konfigurierung Temperatur : 5 ~ 45C Luftfeuchtigkeit : 10 ~ 80% (nicht kondensierend) Temperatur : -25 ~ 60C Luftfeuchtigkeit : 10 ~ 90% (nicht kondensierend) 148.2(W) x 42(H) x 184mm (Einschliesslich front bezel) 740g 125,000 POH(Auslastung 20%)
* Bei PCs ohne Untersttzung von UDMA , kann die Datenbertragungsrate abweichen. 5 6 7 8 9