FCC ID: TLZ-CU484 IEEE 802.15.4 and Bluetooth LE 5.0 wireless microcontroller Stamp LGA Module

IEEE 802.15.4 and Bluetooth LE 5.0 wireless microcontroller Stamp LGA Module AW-CU484 User Guide Rev. A

(For Certification) Revision History Version Revision Date Description Initials Approved A 2020/11/23 Initial Version Shihhua Huang N.C. Chen 1. System Setup

(1) Hardware Requirements Host system need running the Windows10 x64 operating system RF isolation chamber for receive measurements. IQxel-M8 RF attenuators RF cable NFC reader

(2) Software Requirements PL-2303GC Driver Tera Term (tool) Note: Tera Term is our suggestion, you can try any terminal tool. DK6Production flash programmer folder (please contact FAE) Note: You must have below files Mbt.exe (please contact FAE) Note: mbt is our suggestion. You can try any hci tool. 2. How to download the image 1. You must check the COM number (can check the value by the following picture) Note: J9 for DUT COM port 2. Find the folder of DK6ProductionFlashProgrammer, and type cmd to get into the Dos window. 3. Key in ZIGBEE IMAGE:

BLE IMAGE:

DK6Programmer.exe -s com6 -p JN-AN-1242-JN518x-Customer-Module-Evaluation-Tool.bin DK6Programmer.exe -s com6 p qn9090dk6_hci_black_box_bm.bin

*You must note the step. If you key in the format before getting into download mode

(DK6Programmer.exe -s com6 -p JN-AN-1242-JN518x-Customer-Module-Evaluation-Tool.bin), you need to keep holding the ISP button and Reset button, and then release the ISP button after releasing the reset button. To open the tool and download the image file (com6 is your DUT J9 COM port) DUTCOMPORTJ9 4. Select Y 5. Finish 3. Test mode(In Zigbee) 1. Open the Tera Term 2. Select setup Serial port Setting COM port (J9 com port) Baud rate is 115200 Select setup Terminal Receive - select LF Transmit - select CR+LF 3. 4. Select a) standard module 5. Select a) Regular 6. Customer Module Evaluation Tool (main menu) Select g trigger packet test (Rx test) Select I transmit packet test (Tx test)

1. RX test (Select g) g Start test (start to receive the package)

+/- Increment or decrement channel X Return to main menu

/Reset

2. TX test (Select i)

+/- Can control the channel X Return to main menu

/Reset F Fast transmit rate (fast transmit can help modulation to catch signal)

3. NTAG tests(Select n) Select Internal or External NTAG Select a) internal NTAG NTAG Tests (Internal) Select a) read contents of EEPROM Select b) write data to EEPROM

4. Read contents of EEPROM Can read the NFC MAC in Block 0: 04830C3AE26180 Open the NFC Taginfo on you smart phone, and scan the NFC, Then you will get the information from NFC.

5. Write data to EEPROM Use this test to write data to EEPROM, Format is:

1:0 1 2 3 4 5 6 7 8 9 A B C D E F Programs 0 to F in block 1 Check the Format again. 4. Test mode(In BLE) 1. Open the folder of mbt 2. Open the mbt_setup.ini Setting MBT_TRANSPORT=COM3 (your DUT COM port J9) DOWNLOAD_BAUDRATE=115200 APPLICATION_ BAUDRATE=115200 Enable_Debug_Message=1 DOWNLOAD_DELAY = 50

[Solution]

Type=2 3. And type cmd to get into the Dos window. 4. Key in mbt.exe 5. Main menu If you need more information, please key in mbt help. 6. Key in mbt reset Make sure the DUT have been reset.

FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:

This module is intended for OEM integrator. This module is only FCC authorized for the specific rule parts listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed. Additional testing and certification may be necessary when multiple modules are used. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-

frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX FCC ID: TLZ-CU484 ". This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Antenna Information Ant. 1 Brand LYNwave Model Name ALX20M-052AA1 Antenna Type PIFA Antenna Gain (dBi) 2.8 This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil contient des metteurs / rcepteurs exempts de licence qui sont conformes au (x) RSS (s) exempts de licence d'Innovation, Sciences et Dveloppement conomique Canada. L'opration est soumise aux deux conditions suivantes:

(1) Cet appareil ne doit pas provoquer d'interfrences.

(2) Cet appareil doit accepter toute interfrence, y compris les interfrences susceptibles de provoquer un fonctionnement indsirable de l'appareil. IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. IMPORTANT NOTE:

This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains IC: 6100A-CU484 ". The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online.

AzureWave Model: AW-CU480 S/N: J26Z004240 FCC ID: TLZ-CU484 IC: 6100A-CU484 AzureWave Model: AW-CU484 S/N: J26Z004241 FCC ID: TLZ-CU484 IC: 61L00A-CU484 AzureWave Model: AW-CU485 S/N: J26Z004242 FCC ID: TLZ-CU484 IC: 6100A-CU484

AzureWave Technologies, Inc. 8F., No.94, Baozhong Rd. , Xindian Dist., New Taipei City , Taiwan 231 Confidential Letter Date: 2020/11/16 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC IDTLZ-CU484 To Whom It May Concern:

Long Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby respectfully request confidential treatment of information accompanying this application as outlined below:

Block Diagrams Schematics Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We understand that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Short Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby respectfully request short-term confidential treatment of information accompanying this application as outlined below until 90 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device:

External Photos Internal Photos Test Setup photos Users Manuals Sincerely, Applicants company name

: AzureWave Technologies, Inc. Applicants company address

: 8F., No.94, Baozhong Rd. , Xindian Dist., New Taipei City , Taiwan 231 Signature

Name and Job Title

: Patrick Lin / Director E-Mail Tel Fax

: patrick.lin@azurewave.com

: 02-55995599 *5580

: 02-66289666

Module Approval Request Letter Date: 2020/12/4 Subject: Module Approval 2. 3. 4. FCC ID: TLZ-CU484 To Whom It May Concern:

We, Sporton International Inc., are authorized by AzureWave Technologies, Inc. to have their state-of-the-art device approved under module approval authorization. The application of this module is specified to mobile host equipment. The requirements regulated in CFR47 Part 15.212 have been fulfilled and clearly explained below. 1. The requirement of RF shielding: The shielding of the radio portion can be demonstrated in exhibition External Photo. The requirement of buffered inputs: Buffered data inputs stage has been integrated in chipset. The requirement of power supply regulation: The part number of the power regulator is in chipset. The requirements of section 15.203 and 15.204(C): The requirements of antenna connector and spurious emission have been fulfilled. Please reference the exhibition Test Report. The requirement of stand-alone test configuration: Please reference exhibition Test Configuration Photo for the stand-alone test configuration. The requirement of labeling: The instruction on the labeling rule of the end product has been stated in the users manual of this module. Please also see the exhibition Label Sample. The requirement of compliance on specific rule or operating requirements: The required FCC rule has been fulfilled and all the instructions for maintaining compliance has been clearly stated in the Users Manual. The requirement of RF exposure: Please refer exhibition RF Exposure for the compliance of MPE RF exposure rule. 6. 8. 7. 5. Please do not hesitate to contact me for any questions of this request letter. Thank you. Company name

: Sporton International Inc. Company Address

: No.8, Lane 724, Bo-ai St., Jhubei City, Hsinchu County 302, Taiwan, R.O.C. Signature

Name Job Title

: Leo Huang

: Manager Page No.

: 38

AzureWave Technologies, Inc. 8F., No.94, Baozhong Rd. , Xindian Dist., New Taipei City , Taiwan 231 Power of Attorney Date: 2020/11/16 I hereby have entrusted the following person to be a proxy regarding application for Type Address

: No.8, Lane 724, Bo-ai St., Jhubei City, HsinChu County 302, Taiwan, R.O.C. e-mail

: Leohuang@sporton.com.tw I am therefore responsible for the contents of the application. Dear Sir, Certification. Sporton International Inc. Name

: Leo Huang Job Title

: Manager FCC ID: TLZ-CU484 Sincerely, Applicants company name

: AzureWave Technologies, Inc. Applicants company address

: 8F., No.94, Baozhong Rd. , Xindian Dist., New Taipei City , Taiwan 231 Signature

Name and Job Title

: Patrick Lin / Director

: patrick.lin@azurewave.com

: 02-55995599 *5580

: 02-66289666 E-Mail Tel Fax

AzureWave Technologies, Inc. 8F., No.94, Baozhong Rd. , Xindian Dist., New Taipei City , Taiwan 231 SDoC Attestation Letter Date: 2020/11/16 We AzureWave Technologies, Inc., as the grantee of this project (FCC ID: TLZ-CU484 / Brand Name:

AzureWave / Model No.: AW-CU484, AW-CU480, AW-CU485), would like to declare that the composite portion has been authorized under the Supplier's Declaration of Conformity procedures

(Sporton report No.: FD091130, FCC designation number: TW1096). The final product shall consequently comply with the FCC rule applied for SDoC Procedure. Regards, Sincerely, Applicants company name

: AzureWave Technologies, Inc. Applicants company address

: 8F., No.94, Baozhong Rd. , Xindian Dist., New Taipei City , Taiwan 231 Signature

Name and Job Title

: Patrick Lin / Director E-Mail Tel Fax

: patrick.lin@azurewave.com

: 02-55995599 *5580

: 02-66289666