AzureWave / AW-BT261 Bluetooth Module User Manual Install the Bluetooth Driver..2 Connect to other Bluetooth Enabled Devices..7 Uninstall the Bluetooth Driver.11 1 Install the Bluetooth Driver Step1Double click Atheros Bluetooth Software 6.x.x.x Then, InstallShield Wizard will show up and ClickNext. 2 Step2 You will see the installation Destination screen. Step 3. The default destination location is already selected. Click Change to browse to a different destination. 3 Step 4. Click Next. You will see Ready to Install the Program screen. Step 5Click Install to begin installation. You will see Installing Bluetooth XP Suite screen that displays the current settings including user information, setup type, and destination directory. This allows you to review and modify the setup information. 4 5 Step 6Click Next. Bluetooth Suite begins to configure and copy the new software. When the installation is complete, you will see the Finish screen. 6 Step 7Click Finish. You will see a prompt reminding you that before you can use the program, you must shut down and restart your computer. Step 8 Click OK and shut down and restart your computer. The installation is complete. This process creates a Bluetooth Suite shortcut on your desktop. Now you are ready to run Bluetooth Suite. 7 Launching the Bluetooth Suite 1. Insert the Bluetooth Suite USB device into the USB port of your system. NOTE: You can insert the Bluetooth Suite USB device in any USB port. When you do, you will see Found New Hardware message. 2. Double click on the Bluetooth Suite icon on your desktop or choose start > All Programs > Bluetooth Suite > Launch Bluetooth Suite. It displays the blank Atheros Bluetooth Suite screen. NOTE: Wen you launch Bluetooth Suite for the first time, Bluetooth Suite screen may not display any devices within range. It is normal for new installation. You need to click on the Discovery button the top left panel of the window to see all the Bluetooth devices in range. See Figure 2-1. Figure 2-1. Bluetooth Suite Startup Screen During Discovery 8 When the Bluetooth Suite finds devices in range, it displays them. See Figure 2-2 Figure 2-2. Discovered Bluetooth Devices NOTE: Trusted remote devices will show Paired status in Device list, and Connected remote devices will show Connected status in Device list. Other devices will display Inrange status. 9 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Connect the equipment into an outlet on a circuit different from that Increase the separation between the equipment and receiver. to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 10 This device is intended only for OEM integrators under the following conditions:
1) The transmitter module may not be co-located with any other transmitter or antenna, As long as 1 condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: Contains FCC ID: TLZ-BT261. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 11 Canadian Regulatory Wireless Notice This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with IC RF exposure compliance requirements, please follow operation instruction as documented in this manual. This device is intended only for OEM integrators under the following conditions:
1) The transmitter module may not be co-located with any other transmitter or antenna, As long as 1 condition above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: Contains IC:
6100A-AWBT261. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 12 For Taiwan
Note:
1. 2. :
CCXXXXYYyyyZzW 13